Rock Island Standard Compact (CS) 45

Rock Island Standard Compact (CS) 45 (Current Model)

Rock Island Standard Compact (CS) 45 (Current Model)

Whether you are looking for a range gun, a plinker, truck gun, house gun, or something to carry in .45 acp, Armscor/Rock Island may have a model that may interest you.

I purchased one of the Rock Island Standard CS 45 pistols quite a while back when it was known as the Rock Island Tactical Officer. I have had no regrets in doing so, with one caveat that I’ll cover later in this article.

Disassembly and Assembly Is Not Easy - Read Article As To Why

Disassembly and Assembly Is Not Easy – Read Article As To Why

The Rock Island Standard CS 45 is your basic “Officer” length 1911-based pistol with a 3.5”, 6-groove, and 1:16 RH twist barrel. As found on many 1911 clones these days, the barrel is tapered at the muzzle end. After about 600-rounds through the pistol, the barrel locks up tight.

With a 1911-based pistol of this type, a full-length guide rod is a necessary evil and evil it is. Although it helps with reliability and possible accuracy, it does not help when disassembling and assembling the pistol. I’ll touch on that later.

Hogue Rubber Wrap-Around Finger Groove Grips Soon Replaced the Smooth Grip Panels

Hogue Rubber Wrap-Around Finger Groove Grips Soon Replaced the Smooth Grip Panels

My pistol originally came with smooth wood grip panels of which were changed out to Hogue rubber wrap-around finger groove grips, which I believe is almost a necessity with this pistol, both from a recoil control aspect and controllability of the pistol. The smooth wood grip panels would probably work for most shooters but I like a larger grip. Because of the finish on the standard grip panels in the early model, I would not be surprised that the user would change them out for something better. The newer model; however, comes with double-diamond and checkered grip panels.

Slide to frame fit is excellent and tight; I could not detect any play between the two. The frame and slide are Parkerized, and so far, this finish has held up well.

Front and rear sights are plain Jane, although the rear sight is sloped rearward to prevent snagging. I painted the front sight with white sight paint to help them stick out a bit. This gun is not a target gun, but can be an effective UCAP pistol for self-defense. As long as I can catch that front sight at least I know that the pistol is pointing in the right direction. I have not tried to swap out the sights for something better; the existing sights are fine for defensive work and I have heard that it was difficult to fit sights on this pistol (and all Rock Island) pistols because of the sight dovetail dimensions. I don’t know if that is true but I am not willing to spend the money to find out; These sights will do, thank you.

The Back End

The Back End

One issue on my particular pistol was the thumb safety; the plunger spring was weak and there was too much play (for me) with the safety. An aftermarket plunger spring and extended thumb safety was installed by my favorite gunsmith and now the thumb safety is stiffer and very positive moving in and out of safe. Note that the thumb safety that comes with the pistol is extended. The safety is left-side only.

The beaver tail grip safety is nicely done with a memory bump; it extends far enough to keep you hand from crawling up too far on the grip. The mainspring housing is polymer and has vertical serrations. The hammer is skeletonized and serrated for easy cocking/decocking.

The slide lock is standard fare, but checkered for ease of use. I can reach the slide lock lever easily without really changing my grip – even with the Hogue rubber wrap-around finger grove grip. Your experience may differ, however.

The magazine release is not extended but is easy to reach and is also textured for easy purchase. The left-side only magazine release button releases magazines with no drag and magazines insert fully and lock in positively when inserted fully into the beveled magazine well. Magazine capacity is 7-rounds and a Nighthawk Custom Act-Mag magazine comes with the pistol. The RICS uses any 1911 magazine so replacements are easy to find.

For a pistol in this price range, the trigger is excellent and is a short-throw trigger. My RICS has a skeletonized trigger but lacks the over-travel adjustment of later models. Over-travel on my version of this pistol is virtually non-existent so no adjustment is needed. The trigger breaks crispy-clean at 4.5 pounds with very little take-up. In fact, I have more expensive 1911-based pistols that have more take-up and over-travel than this with this pistol.

The slide has fine vertical serrations on the rear of the slide for gripping. No press check capabilities are provided (front serrations), nor is a way to check for a chambered round; this must be done by slightly pulling the slide slightly rearward – just like in the old days. Of course, if I see a closed chamber, I automatically think that the pistol is loaded and chambered.

My version is roll-marked on the slide but lack the highlighting of later models.

The RICS, like “real” 1911-based pistols utilizes an internal extractor and “70” series features. On the same side as the extractor is the lowered and flared ejection port.

The RICS is very reminiscent of the original Colt “Officer” model with the exception of the finish; don’t expect polished blued steel on this one. With that said, and with this pistol made of steel, the pistol is heavy and weighs a healthy 2.16 pounds unloaded and 2.43 pounds with a full magazine of seven rounds and just a tad more with 7+1 rounds.

A Heavy Paper Clip May Be Required for Complete Disassembly and Assembly - And Usually Is

A Heavy Paper Clip May Be Required for Complete Disassembly and Assembly – And Usually Is

Remove and Install the Guide Rod "Assembly"  from the Inside Out

Remove and Install the Guide Rod “Assembly” from the Inside of the Frame

The Guide Rod "Assembly" Held Captive By the Paper Clip

The Guide Rod “Assembly” Held Captive By the Paper Clip

One of the major complaints is the disassembly technique with pistols using one piece guide rods. Unfortunately, with a pistol of this length of barrel, one piece guide rods are a necessity. Disassembly of the pistol is not that bad, really.

After ensuring that the pistol is unloaded and the magazine removed, cock the hammer. Then, pull the slide rearward to engage the slide stop.

move the slide to the disassembly notch and remove the slide stop pin. Then, while holding the slide and frame, carefully slide the slide off the frame. There are two precautions in doing this; the recoil spring is not captive and if you are not careful, you can pinch the hand as the slide moves forward under tension – that will hurt. I usually force the slide rearward to the disassembly notch with the left hand. Then use the right hand to hold it in that position as I remove the slide stop with my weak hand. While still holding the slide, I use the left hand to slowly remove the slide from the frame.

Once the slide is off the frame, you can remove the guide rod and recoil spring; it might take some wiggling, as the there is a guide rod bushing that holds the guide rod in alignment. Once the guide rod and recoil spring is removed from the pistol, the guide rod bushing is removed toward the rear of the slide. The barrel can then be removed. In some cases; however, the guide rod is too tight inside the bushing to clear the frame that surrounds the swing link. In this case, the guide rod must be pushed forward under spring tension until the “captive” hole clears the front of the slide. A heavy paper clip is then inserted slightly through the hole. The paper clip holds the guide rod, recoil spring, and guide rod busing as an assembly. Then, the paper clip is bent forward, which allows the recoil guide “assembly” to be removed and the barrel is removed in the usual fashion. That was fun, huh?

Dissembling the "Captive" Guide Rod

Dissembling the “Captive” Guide Rod

Modified Barrel Bushing Wrench Makes Disassmbling and Assembling the "Captive" Guide Rod Assembly Easy

Modified Barrel Bushing Wrench Makes Disassmbling and Assembling the “Captive” Guide Rod Assembly Easy

The “captured” guide rod assembly can be disassembled for cleaning and lubrication and I have made a special tool to do the disassembly and reassembly. Essentially, a hole was drilled in the center of a standard bushing wrench. The hole is slightly smaller than the base of the guide rod bushing. I can simply push the guide rod bushing downward while maintaining pressure on the assembly with the wrench. I can then remove the paper clip and slowly allow the guide rod bushing to come off the assembly while maintaining pressure on it with the modified bushing wrench. Reassembly is just the reverse; place the guide rod, recoil spring, and guide rod bushing into place. With the modified bushing wrench in position on the guide rod bushing, compress the recoil spring until the hole in the guide rod is revealed. Place the paper clip into the hole and gradually allow the guide rod bushing to seat against the paper clip.

The best is yet to come – assembling the pistol.

Guide Rod Bushing Butts Against the Inside of the Slide and is Held In Place under Spring Tension

Guide Rod Bushing Butts Against the Inside of the Slide and is Held In Place under Spring Tension. In early Models, the Guide Rod Will Ride Up and Prevent the Slide From Being Installed On the Frame

The barrel is slid into the slide as usual and then it gets crazy. The “captive” guide rod is pushed in from the rear of the slide. Note also that the guide rod bushing has a cutout that matches the mating surface of the slide.

In some pistols, the guide rod “assembly” can be pushed forward, and while holding the guide rod in place under spring tension, the paper clip is removed and the guide rod released slowly until it rests against the swing link base. The base of the guide rod tries to ride up and over the swing link and the frame cannot slide onto the slide fully, as the guide rod base prevents it from doing so.

Slightly push the guide rod forward and hold it against the barrel Slide the slide onto the frame, release the guide rod once it is in the frame, locate and press the slide stop through the swing link, and align the slide stop with the slide stop notch in the frame. The slide will be under spring tension until the Slide Stop is fully seated.

Pull the slide slightly to the rear to release the Slide Stop. Then, while holding the slide, allow the slide to move forward slowly until it is in battery.

Perform a function check.

The Working End of the Rock Island Standard Compact - Note Marks on Recoil Guide Bushing From Using the Large and heavy Paper Clip  Used During Disassembly and Assembly

The Working End of the Rock Island Standard Compact – Note Marks on Recoil Guide Bushing From Using the Large and heavy Paper Clip Used During Disassembly and Assembly

Aside from the problems of putting the pistol into pieces and putting it back together, it is a good range performer. The RCIS is actually more accurate than a Colt Series 80 MKIV “Officer” model that I once had. The RICS really likes 230-gain ammunition and has fed ball and hollow point bullets without interruption. With the weight of the pistol, accompanied by a good set of grip to help with control and recoil, the pistol is quite capable of “combat” accuracy at 15 yards although I would keep defensive ammunition somewhat below 900 fps to reduce muzzle flip – and this pistol has some healthy muzzle flip with anything above 850 fps (which, by the way, was the original velocity for 230-grain ball ammunition). With that said it did well with Remington 230-grain Golden Saber and it would be a good defensive round to carry in this gun.

Rock Island Standard Compact Rides Nicely in a Modified CBST Holster (The same holster that I now use for the Ruger SR1911CMD-A)

Rock Island Standard Compact Rides Nicely in a Modified CBST Holster (The same holster that I now use for the Ruger SR1911CMD-A)

Although not pretty, the Rock Island Standard Compact 45 is more than fit to fill the role of personal defender. It has many of the features found on more expensive 1911-based pistols, has an excellent short throw trigger, and is a reasonably-priced package.

Aside from the initial light plunger spring and loose fitting thumb safety, which was easily corrected, the pistol has been a fine shooter with no failures to date. While slightly on the heavy side for concealed carry, it would make a fine pistol to have in one’s vehicle or when in environments where you do not want to bang up that more expensive defensive tool.

UPDATE 01/17/2016 – Bottom Drawer Pistol – Top Drawer Performance:

100 Rounds, 230-grain FMJ, 10-yards, offhand from Modified Weaver. First shot was high To Get My Bearings - Ninety-Nine Subsequent Shots Were Not

100 Rounds, 230-grain FMJ, 10-yards, offhand from Modified Weaver. First shot was high To Get My Bearings – Ninety-Nine Subsequent Shots Were Not

This morning was range time and I decided to take the Rock Island Armory CS Standard with me. I have been working on this pistol; trying to correct what a “gun smith” did in replacing the thumb safety. While I have made the thumb safety better in moving from one position to another, I still have to do some very minor buffing to the “detent transition area” for lack of a better definition. A combination of factors contributed to the issue; a heavy Plunger Spring and an over-sized thumb safety pin, which made it extremely difficult to engage the thumb safety. But, I digress from the purpose of this posting.

Granted, the Rock Island Armory family of 1911-based pistols are not top drawer. In fact, some would consider bottom drawer. Since I am a bottom drawer type of fellow, I own a couple of them. The first RIA pistol was a FS Standard – essentially the G.I Model. The RIA CS Standard was my second RIA purchase and it came with a somewhat loose thumb safety; it was quite the floppy fellow. I turned it into a gun smith for a replacement thumb safety and went from too loose to too tight. I doing the work myself to find a happy medium. Yesterday, I got the thumb safety to work better but it was still stiff – stiff enough to make my thumb sore trying to get it into the safe position. I thought that I would run the RIA CS this morning to (hopefully) loosen up the safety just a tad. While that did not happen, the performance of this pistol had several people considering the Rock Island Armory line of pistols.

I ran 100 rounds of 230-grain FMJ ammunition through three different magazines; a flush fit 7-round TRIPRESEARCH,com, a 7-round ACT-MAG that came with the pistol, and a Wilson Combat 7-round magazine with bumper pad. All three magazines worked just swimmingly. However, that is still not the point in all of this.

The accompanying image show the result of 100 rounds of 230-grain FMJ going downrange at 10-yards distance. My first shot was the one in the 9-ring. Once I figured out that the pistol is a POA pistol, the remaining 22,770 grains of JHP went in the 10-ring. Shooting was offhand and slow-fired from a modified Weaver with box stock sights (plain Jain “tactical” with no dots) and trigger that I can only say is fantastic considering the price of the pistol. There was also no failures out of this “Officer” model bottom-drawer 3.5-inch barreled pistol.

In my opinion, the Rock Island Armory 1911-based pistol family, like the Bersa family of pistols, is very underrated.

See the complete line of Armscor/Rock Island pistols @ https://us.armscor.com/products/

Loading

About Taurian

Taurian is a U.S. Army veteran and former LEO and Defensive Tactics Instructor. Taurian also has over fifty years of experience as a Technical Writer and Training Program Developer. After leaving home at the age of ten without any shoes, Taurian continues on with many years devoted to the keeping and bearing of arms.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.